APE100 project

This document describes a parallel processor for large scale scientific computations. This machine is based on the experience acquired with the APE computer. It is a fine grained SIMD processor, delivering a peak speed higher than 100 GFlop. This performance is, for instance, required for high precision computations in Quantum Chromo Dynamics [QCD]. The system and hardware architectures are described.

APE100 Architecture

APE100 is a SIMD (Single Instruction Multiple Data) parallel computer with a tridimensional architecture based on a cubic mesh of nodes. Each processing node is connected to its six nearest neighboursin all three space dimensions. Periodic boundary conditions are used to wrap around the mesh. The main advantage of this simple structure is modularity. The configuration of APE100 is scalable from 8 to 2048 nodes.

Each node is composed of a single precision 32 bits IEEE-754 floating point processor, (the MAD), a 4 (or 16) Mbytes RAM bank and the logic for node-to-node communication. Parallel processing on APE is limited to operations on floating point numbers. Each node is capable of 50 Mflop so that the complete configuration has a performance of 100Gflop. There is a Controller for each group of 128 nodes and all the Controllers execute exactly the same code.

The Controllers are based on a scalar processor named Z-CPU which executes the user program, all integer operations and delivers the microcode and the data addressing to the nodes. The Z-CPU has its own data memory, program memory and registers.

The APE100 synchronous core (i.e. the Z-CPU's and the nodes described above) is connected to a host computer through an asynchronous interface, called AI (Asynchronous Interface), based on a network of transputers which act as front end. The user program runs on the synchronous core.

This asynchronous interface is able to access all the resources of APE100: control registers and memory banks of the synchronous core as well as the parallel mass storage system. The host communicates with the AI by using transputer links. The system code running on the AI is able to convert requests coming from the host (on the transputer links) into operations on the APE100 machine, as well as to serve interrupts arising from the synchronous machine. Most part of the system software runs on the host computer while the real time kernel of the operating system runs on the AI.

This below is a sensitive map showing the overall synchronous core of a Ape installation.

APE100 Software Survey

• Preface
• Overview
• The compilation system
• Zz and the TAO language
• The operating system
• The symbolic debugger
• The system service mechanism and the exception handling
• The APE100 tools

Preface

This paper describes the APE100 system software architecture and its major components: the compiler, the operating system and the debugger. The TAO language, as well as the debugger command language, are incremental languages based on Zz, an innovative dynamic parser. Zz and these language are shortly described in the following. Some major utilities, simulators and analysis tools are also described.

Overview

We can divide the system software of APE100 into its major components: the compilation system, the operating system and the APE100 utilities. The symbolic debugger and some system services interact with the three components and require a separate discussion.

All the system software code is written in C-language to ensure portability.

The compilation system

The compilation system runs on any conventional computer, usually the same host connected to APE100. Two types of source languages are supported by the compilation system: TAO and the APE100 assembler. Assembly language is used for writing diagnostic or system programs. The user is strongly suggested to write his programs using the TAO language: it is easier to use and produce object code which is more optimised.

The compilation system of APE-100 can be divided into two steps. The first one reads a source file and produces an intermediate APE relocatable code file (.IAR). This file can be linked with other modules in the second step. In the second step the linker collects the modules and the code generator produces a loadable and executable file (.ZEX).

In the case of an TAO source the first step of the compilation system uses the Zz dynamic parser linked with routines which perform some optimizations and produce the .IAR file and, optionally, a macro assembly source listing. The optimization done at this level is only oriented to reduce the number of memory to register I/O operations a much more sophisticated optimizer is being developed. The compiler, therefore, attempts to use as much as possible the machine registers. In this phase of the process floating point registers are considered as an unlimited resource. Floating point registers assigned in this phase are called virtual registers.

The .IAR format supports physical registers and virtual registers. The virtual registers are assigned to physical registers during the final optimization step. The APE assembly is in (near) one-to-one correspondence with the content of the .IAR file. The same routines used by Zz to produce the .IAR are called by a macro expander to compile macro Assembler source programs.

The main difference between a .IAR produced from the TAO language and from the macro Assembler is that the first uses virtual registers and relocatable addresses, while the second uses physical registers and memory locations (directly allocated by the programmer). The two kinds of optimization done from the second step are: Code compaction and temporized microcode generation.

One of the main tasks of the code compaction program is that of combining floating point additions and multiplications into multiply-and-add operations, which are called "normal" operations because the architecture of the floating point processor (MAD) is optimized for them. To increase the number of "normals" produced, the associativity of the add (and subtract) operations can be changed.

Other optimizations done by the current code reducer are:

• folding: compile-time execution of operations with known result, like multiplications by zero or by one,
• deletion of unnecessary move operations produced by the first step of the compilation chain,.
• deletion of dead code (operations whose result is not used, like those arising from the trace of a matrix product).

The main task of the microcode generator is to rearrange the instructions in order to fill the pipeline. From the point of view of the microcode generator APE-100 can be treated like a machine consisting of two parts which are completely synchronous: the integer processor (the ZCPU), which is in charge of integer calculations, address generation and flow control, and the floating point processors (the MAD's) which do most of the number crunching. The internal architecture of these two parts is quite similar allowing a single code generation phase.

The MAD and the ZCPU are VLIW (very large instruction word) pipelined chips. A single instruction will affect different devices, which correspond to different instruction bit fields, at different times on both control words (the MAD control word and the Z-CPU one). In order to fill the pipelines, the MAD- ZCPU microcode producer is free to completely reschedule both floating point and integer instructions, with two constraints: no device can be taken by two instructions at the same time, and no instruction can execute before its operands are ready.

After scheduling, the code producer maps all the MAD virtual registers to physical ones. This phase does not concern the ZCPU part of the code, since its registers are always treated as physical. Compilation may fail at this point if there are not enough physical registers to satisfy all requests. Given the large size of the MAD register file (128 registers), this is a rare event, usually caused by an large use of Register and Phys Reg variables (see the TAO language manual). We hope in the future to improve the situation by the automatic "spilling" of excessive registers into memory. The problem of register spilling is a very complex one and has not been tacked yet.

Our optimization chain has been proved to be highly effective for many different codes. The performance of an optimised QCD code is near of 80% of the machine peak performance.

All the informations describing each assembly code: number of operands, result times, device occupation times, code bitfields, etc. are defined in tables which are read at the startup of the microcode producer. It's possible to compile these tables from a source file written in a machine description language suited for a general APE architecture and have them read by the compiler at startup. This feature is used to develop new hardware architectures, it was used to define the MAD processor and is now evolving to define more complex architectures.

The predecessor of the single-chip Controller, the ZCPU, was called S-CPU. It had an architecture different from that of MAD. The code production for machines with a S-CPU controller had to be performed in two distinct phases: one for flow control instructions and addressing and one for MAD' instructions. Only the MAD microcode was suitable for pipeline optimization.

ZZ and the TAO language

Dynamic compilers are compilers able to follow the evolution of a grammar during source program compilation. Dynamic compilers and growing grammars allow the compilation of programs written in programming languages adapted to the problem at hand. Some of us have defined a theoretical framework for "evolving grammars" and "dynamic compilers" [4].

Dynamic compilers easily perform purely syntactic strong type checking and operator overloading. A dynamic parser ("Zz Parser") has been developed and has been successfully employed by the APE100 group to develop the APE100 compiler, the symbolic debugger and other system software tools. Using Zz we have defined a starting language inspired by the familiar FORTRAN syntax. This starting language, TAO, is very similar to a new generation FORTRAN language with parallel support instructions, flow control instructions and integer, float and complex data types and operators. The programmers may use the Zz dynamical compiling features to extend the predefined TAO language, adding new syntaxes and features suitable for their applications and creating Language Extension Libraries (LEL). The starting language itself is defined in a LEL. We have built a number of LEL's. The QCD extension library ("qcd.hzt"), for example, defines the compilation rules for QCD specific data structures (e.g. su3 matrices and spinor data types) and makes available an appropriate set of QCD specific statements and operators (e.g. gamma operators, multiplications of su3 "variables", ...). Other problem specific LEL's have been defined for fluid dynamics, neural networks and for other promising areas of application of the APE100 machine.

The application code written by the APE100 users using an evolving language are several times shorter than programs written in conventional programming languages, due to the easy introduction of convenient operators, statements and data types. The opinion of the APE100 user community is that these factors greatly enhance the quality and readability of the resulting application programs.

The FORTRAN-like flavour of the TAO starting language will probably look familiar to any programmer of scientific applications. It is the smoothest transition path from a standard computing environment to the APE100 parallel environment. The TAO language is not a FORTRAN with a number of non portable extensions. Our programming language has been designed to allow easy and efficient coding of scientific applications on a parallel computer with unusual architectures. The actual implementation can be considered as a subset of a more general TAO dynamic language which has been defined by the APE100 collaboration. A typical novice user may well start writing programs in the TAO language. As he acquires more confidence in the language, he will probably include more and more advanced Zz features, in order to write more compact, readable and easily maintained programs.

Differences with more traditional FORTRAN-like languages can be noticed in two main areas: a) parallel features have been introduced in the language. As an example, parallel data structures can be defined, and new instructions are defined for (parallel) branch control. Several features of the language in this area have been tailored to the APE100 architecture. b) features typical of more structured object oriented languages (like the C++ language) have been introduced. An important example in this line is the definition of several data structures (e.g. SU(3) matrices and spinors) frequently found in QCD simulation programs as well as corresponding operators.

In the following we describe some of peculiarities which are strongly related to the hardware architecture of the APE100 computer family. Every time the APE100 programmer declares a data structure, an appropriate amount of local storage will be reserved for it on each node (at the same local address for all nodes) and logically associated to the name of that data structure.

All nodes of APE100 execute the same code (although acting on different data). This means that each operation written in TAO language, acting on some floating point variables actually activates the same operation on every node of the mesh. The data items contained in the local storage corresponding on each node to the program variables are the operands of the operation executed by that node. Integer variables are defined on the ZCPU only. Integer arithmetics in a typical APE100 programs should involve mainly (but not necessarily only) the evaluation of addresses for the local (floating point) variables, as well as some arithmetic or logic manipulation of control variables (e.g., loop indexes). The 32 bit integer data type should be used when declaring the addressing, loop indexing and array indexing variables stored on the "flow control and addressing unit" (ZCPU, Controller).

On APE100 there are three types of conditional branch instructions, according to the type of conditions which can be tested to alter the sequential flow of program execution. Two such instructions may cause an effective branch in the program flow. The third instruction is locally managed by each node and may result in a temporary suspension of the program execution on that node. The last feature allows a crude form of local program conditioning. The first type of condition is tested on integer variables defined on the ZCPU. This type of condition can be inserted in standard "if" statement. A second type of condition involves local data defined on each node of the array, but used in a global way. The control condition can be the obtain as the logical AND or the logical OR of the conditions evaluated on all nodes. This type of condition can be also inserted in "if" statements, alone or combined with the standard conditions discussed before.

   Examples: {?}
        if All (local condition)
             { statements }
        if (Any (local condition) && (integer condition) )
             { statements }

In the first example the global condition is the AND of local ones. In the second a global condition results from the OR of local ones is combined (&& stands for logical AND )

The third type of condition is local to each processing node. This type of condition is used in a special TAO instruction, called "where". The "where" instruction does not alter program flow. Rather, instructions contained within the where clause are executed on only those nodes where the relevant condition is true. Instructions are converted to nops (no-operations) on those nodes where the condition is not met.

The APE100 architecture supports data access of each local node to its own memory bank, or to the memory banks belonging to its six nearest neighbours of the three-dimensional grid of processors. Access to memory banks belonging to far-away processors can of course be programmed as a sequence of hops among adjacent nodes. The memory bank selected for (local or remote) access is specified at run time by the program in terms of the highest significant bits of the address. An example will make the previous statement clearer. Assume that v[i] is an TAO vector. The program sequence a = v[2+RIGHT] copies onto variable a in each node the value v[2] taken fro the node on the right. RIGHT is an integer constant defined with the proper bit pattern. This operation is accomplished independently on all processing nodes.

The operating system

The APE100 Operating System provides the user of APE100 with a set of functionalities to load and run the programs which have been cross-compiled on the host, to monitor and debug the program execution and optionally to access the hardware resources of the machine, for example to read or write registers and memories.

The operating system is composed of two layers: a real time kernel running on the Asynchronous Interface (AI) and the system programs running on the host. The two major system programs of the operating system, running on the host, provide the interface to run (RUNQ) or to debug (DEBQ) the user program. The RUNQ utility downloads the executable user image on the memories of the synchronous core and starts the program. Also, it waits to serve the system services requests arising from the user program involving the host.

In a following section we'll show some details of the symbolic debugger DEBQ, it's architecture and implementation.

Both these applications allow the user to identify the last source instruction executed when the user program abnormally terminates due to an exception.

The real time kernel of the APE100 operating system is composed of several processes running on the different processors of the asynchronous interface. These kernel processes are always running on the AI since the machine is booted at power on. The main tasks of the kernel are:

   * Serving the requests coming from the host that are usually issued by system applications (RUNQ and DEBQ) or by system diagnostic program.
   * Serving the interrupts, traps, exceptions and other asynchronous events generated by the user program and by many hardware watchdogs.
   * Handling the AI network and any needed communication with the host and the parallel mass storage system.

The symbolic debugger

DEBQ is the symbolic, source level debugger provided with APE100. DEBQ provides an interface to APE100, which enables the user to load, run and debug his programs and to set the preferred machine configuration. The user can stop the execution of the program at specified breakpoints and he can display and change the values of the variables used in the program. It is possible to debug the user programs referring to the source code and to the same variable names used in the TAO source. It is possible to inspect and modify the machine memories and registers and step over machine cycles. The user works at his terminal which is connected - possibly by means of a computer network connection - to the host of APE100. DEBQ uses the functions of the real time kernel to access the machine registers and memories as well as the program memory. On-line help is available to provide the user with a description of the command set and with the command syntax.

Commands are available to set different machine configurations and defaults and to access APE100 data memories directly by means of absolute addresses. The latter are particularly used when debugging programs written in assembly language.

DEBQ uses interactively the Zz parser. Consequently DEBQ itself has dynamic parsing capabilities which are available in the user interface. Moreover DEBQ uses the dynamic capabilities of the Zz parser to get and keep informations about the types and the variables used in the program being debugged. In fact, when an executable program is loaded, DEBQ reads a Zz source file, namely the .SMB file, and builds the grammar production rules that will enable it to recognize the variable names used in the program. The .SMB file is written by the compiler and consists of a set of production rules that describe the variables used associating each variable name with the variable type, the memory (scpu or fpu) it refers to, the address where the variable is allocated, the variable dimension and so on. As a first approximation, the production rule (in the .SMB file) for a real variable could be like the following:

   real_var->alfa {/return [xx,yy]}

where 'alfa' is the variable name, xx the address where alfa is allocated, yy the number of items and real_var is the variable type. The production rule for a structured object is much more complicated. When DEBQ reads this file, these production rules are accepted by the parser and the grammar is incremented. DEBQ will then be able to recognize user commands it was not able to recognize before (for example 'PRINT ALFA') and it will call the low level procedure to read a datum from APE100 memory passing it the right address. In this way it is possible to connect the compiler and the debugger by means of production rules of an evolving grammar.

A debugging session starts when the user loads the .SMB files. From this point on, the user has several chances, the main of which are described in the following. He can examine the values of all the variables he used in his program, as well as some system variables, referring to them by name. The variables can be of any data type: simple items and structured ones either pre-defined or built-in with the type constructors, e.g. complex, su3 etc. Portions of a structured variable - e.g. individual fields of a record - can be examined independently.

The user can modify the content of the variables. In fact, by means of the deposit command, it is possible to assign a new value for one or more variables or for a part of a structured variable. Zz takes care of type checking. It is possible to modify a variable on a single node or in broadcast mode and to examine a variable both on a single node or on a mesh.

Suitable commands are provided to list the names, the types, the dimension and the address of one or all variables used in the source program.

Before running the program the user can set one or more breakpoints at different lines to follow the program execution. During the run, when a breakpoint is reached, the execution is stopped and the source code is displayed. It is then possible to inspect the variables and to assign new values to them. It is also possible to set other breakpoints or to cancel the ones already set. The program can be restarted from the point where it stopped. It is not actually possible to set a breakpoint at every source line. In fact, the operations' order in the APE100 executable code is quite different from that of the source code, because of the optimization made at compilation time with the goal of filling the MAD pipe. It is possible to set breakpoints only at those lines where the pipeline is empty. As an example it is always possible to break at any point of branch, label or routine call. The source shown by the debugger is annotated in order to identify breakable instructions.

The system service mechanism and the exception handling

The user programs running on the synchronous core of APE100 has to request the system intervention to perform I/O operations and more generally to perform any kind of asynchronous operations.

The user program uses in any case the mechanism called "System Services request".

Several types of System Service are implemented: the timer function, the generation of pseudo random numbers, the exception masking, and the most important of them, namely the Input/Output functions.

The execution of a System Service takes place by halting the user program flow by means of a trap instruction and so doing passing the control of the program to the system code running on the AI.

The user program, before trapping, prepares a packet of data describing the required service and stores it in a predefined memory area. When the trap is executed the user program halts and raises an exception. This halt-interrupt is detected by the AI and the system service handler is invoked.

The system service handler reads from the memory the information describing the required service and undertakes the proper actions to satisfy the request. If the required service is an I/O operation involving the host I/O system, the AI requires the intervention of the host. Then, the data are transferred via transputer links from the APE100 memories to the host or viceversa.

Usually at system service completion the operating system resumes the user program. A special system service is used to signal the program completion. This service does not restart the user program and notifies the exit status to the host.

When an exception is raised (following any kind of abnormal event) the user program is halted and the system code running on the AI is alerted. If the user program has declared a proper exception handler the operating system resumes the user program at the given entry point elsewhere a diagnostic message is sent to the host.

By default the TAO compiler defines a standard exception handler to properly manage user program exceptions.

The APE100 tools

A lot of tools have been developed to help the user or a system programmer: Any kind of object code can be examined, there exist tools to dump or load memories in different formats and the portability of APE100 executable images among different hosts is guaranteed.

A couple of utilities have to be shortly described: The performance analyser is a very useful tool to obtain an idea of the performance of an TAO program. When the program is compiled this utility is able to generate an annotated source listing. Columns are added to the source program, showing the first and last cycle of all floating point instructions pertaining to a line, and for every code section the percentage of efficiency (effective vs. maximum Flops) is given. Efficiencies of more than 80% are achieved in good cases.

We produced a simulation program oriented to a deep (hardware) simulation, in order to follow step-by-step the execution of the code. To this end the program represents each logic block of MAD to the gate level. This simulator is of course slow and suitable for small programs and system debugging.

There exist also a program that translates an Intermediate APE Code file (.IAR ) into a semantically equivalent C one, thus allowing an hardware independent simulation, useful to test large programs or the higher levels of the compiler chain.