Difference between revisions of "SHAPES project"

From APEWiki
Jump to: navigation, search
(Material Expensives)
m (The Distributed Network Processor: HW architecture)
 
(18 intermediate revisions by the same user not shown)
Line 1: Line 1:
== Activities reports 2006 ==
+
== INFN Roma group in the SHAPES project ==
+
The INFN Roma group's contribution to the [http://www.shapes-p.org SHAPES] project consist of a TLM-SystemC and a VHDL model of the DNP.
=== Working Hours on Shapes Project ===
 
  
Lo Cicero Francesca:
 
  
Perra Mersia:
+
=== The Distributed Network Processor in the SHAPES Tile ===
 +
DNP stands for Distributed Network Processor. The main task of the DNP is to provide inter-tile communication services.
 +
A secondary service is to act as a DMA controller for intra-tile communications. The DNP offers its services to other masters in the tile, typically a RISC or a DSP processor.
  
Sidore Carlo:
+
The picture below shows the DNP in the RISC-DSP Tile (RDT).
 
=== Material Expensives Reports ===
 
  
=== Business Trip Cost Reports ===
+
[[Image:DNPin_the_RDTile.jpg]]
  
=== Management Reports ===
+
=== A scalable architecture: the DNP and the interTile communication ports ===
 +
 
 +
The SHAPES architecture is a scalable architecture, based on tiles. The scalability is assured by the DNP which provide a set of inter tile communication port for on-chip and off-chip communications.
 +
The on-chip communications between tiles is guaranteed by the Spidergon NoC, while the off-chip links are based on a serial protocol to support 3D lattice architectures.
 +
 
 +
==== One chip, multiple tiles ====
 +
 
 +
An example of SHAPES chip, is showed below:
 +
 
 +
[[Image:DNPintheCHIP_small.jpg]]
 +
 
 +
The pictures show as the DNP is the communication engine in the shapes tile. It support the communication inside the tile via two masters ans one slave AHB AMBA ports, and outside the tile with a NoC port and six links for 3D connections. The DNP is designed to support another link for the collective. The collective link allows direct connections between nodes not connected by the 3D lattice.
 +
 
 +
==== The SHAPES tile in a 3D lattice ====
 +
 
 +
[[Image:SHAPES3Dlattice_ex.jpg]]
 +
 
 +
=== The Distributed Network Processor: HW architecture ===
 +
 
 +
The DNP receives commands issued on a slave port by the initiating processors (the RISC or the DSP). One command is done by 8 words.
 +
 
 +
[[Image:command.jpg]]
 +
 
 +
The DNP is also equipped with two master ports to sustain the data traffic on the AMBA Multilayer bus. In a typical situation those master ports act simultaneously to sustain the flow between the source and the destination device (memory buffers exposed to the DNP by the tile: i.e. DXM, DDM, DPM, RDM, RPM, POT).
 +
For intra-tile communications, the set of master and slave interface ports would suffice. For inter-tile communication, which require the cooperation of at least two DNPs located on different tiles, the DNP is equipped with a set of inter-tile interfaces. A first set of those interfaces are used for off-chip communications on a 3D toroidal next-neighbors topology and on a collective communication tree. A second set of interfaces will be used for on-chip communication through a dedicated NoC architecture.
 +
The DNP's brain are the inner blocks called ENGINE, ARBITER and ROUTER.
 +
 
 +
[[Image:dnp_HW_spec_v1_small.jpg]]
 +
 
 +
The data inside the DNP and in the whole set of the inter tile ports travels as packet.
 +
The ENGINE's main task is to interpret the commands coming from the intra tile bus (AMBA AHB in this version) via the AHB TLM Slave port. Other ENGINE's task is to support the intra tile master blocks in building the packets once the command has been already decoded (see next chapters for more details).
 +
 
 +
[[Image:packet.jpg]]
 +
 
 +
The ARBITER and the ROUTER, applying a priority scheme and a fixed routing algorithm, take care to drive the packets from one DNP port to another DNP port.

Latest revision as of 15:31, 20 September 2007

INFN Roma group in the SHAPES project

The INFN Roma group's contribution to the SHAPES project consist of a TLM-SystemC and a VHDL model of the DNP.


The Distributed Network Processor in the SHAPES Tile

DNP stands for Distributed Network Processor. The main task of the DNP is to provide inter-tile communication services. A secondary service is to act as a DMA controller for intra-tile communications. The DNP offers its services to other masters in the tile, typically a RISC or a DSP processor.

The picture below shows the DNP in the RISC-DSP Tile (RDT).

DNPin the RDTile.jpg

A scalable architecture: the DNP and the interTile communication ports

The SHAPES architecture is a scalable architecture, based on tiles. The scalability is assured by the DNP which provide a set of inter tile communication port for on-chip and off-chip communications. The on-chip communications between tiles is guaranteed by the Spidergon NoC, while the off-chip links are based on a serial protocol to support 3D lattice architectures.

One chip, multiple tiles

An example of SHAPES chip, is showed below:

DNPintheCHIP small.jpg

The pictures show as the DNP is the communication engine in the shapes tile. It support the communication inside the tile via two masters ans one slave AHB AMBA ports, and outside the tile with a NoC port and six links for 3D connections. The DNP is designed to support another link for the collective. The collective link allows direct connections between nodes not connected by the 3D lattice.

The SHAPES tile in a 3D lattice

SHAPES3Dlattice ex.jpg

The Distributed Network Processor: HW architecture

The DNP receives commands issued on a slave port by the initiating processors (the RISC or the DSP). One command is done by 8 words.

Command.jpg

The DNP is also equipped with two master ports to sustain the data traffic on the AMBA Multilayer bus. In a typical situation those master ports act simultaneously to sustain the flow between the source and the destination device (memory buffers exposed to the DNP by the tile: i.e. DXM, DDM, DPM, RDM, RPM, POT). For intra-tile communications, the set of master and slave interface ports would suffice. For inter-tile communication, which require the cooperation of at least two DNPs located on different tiles, the DNP is equipped with a set of inter-tile interfaces. A first set of those interfaces are used for off-chip communications on a 3D toroidal next-neighbors topology and on a collective communication tree. A second set of interfaces will be used for on-chip communication through a dedicated NoC architecture. The DNP's brain are the inner blocks called ENGINE, ARBITER and ROUTER.

Dnp HW spec v1 small.jpg

The data inside the DNP and in the whole set of the inter tile ports travels as packet. The ENGINE's main task is to interpret the commands coming from the intra tile bus (AMBA AHB in this version) via the AHB TLM Slave port. Other ENGINE's task is to support the intra tile master blocks in building the packets once the command has been already decoded (see next chapters for more details).

Packet.jpg

The ARBITER and the ROUTER, applying a priority scheme and a fixed routing algorithm, take care to drive the packets from one DNP port to another DNP port.